在華爲三層交換機上創建VLAN，端口劃分，三層VLAN接口地址配置，靜態路由或是RIP協議配置。跟小編來學習一下配置過程。
靜態路由配置過程：
PCA:ip address: gw:(VLAN2路由接口IP位址)
PCB:ip address: gw:(VLAN3路由接口IP位址)
PCC:ip address: gw:(VLAN2路由接口IP位址)
S3526A和S352B之間的互聯網段爲、24
分配S3526A VLAN4路由接口IP位址爲,S3526B VLAN4路由接口IP位址爲
三層交換機配置
創建VLAN，把PC劃到特定VLAN中：
//創建VLAN
[S3526A]vlan 2
//把端口劃到VLAN中
[S3526A-VLAN 2]port ethernet0/9 to ethernet0/12
[S3526A-VLAN 2]vlan 3
[S3526A-VLAN 2]port ethernet0/13 to ethernet0/16
[S3526A-VLAN 2]vlan 4
//交換機B的配置：
[S3526B]vlan 2
[S3526B-VLAN 2]port ethernet0/9 to ethernet0/12
[S3526B-VLAN 2]vlan 4
配置各臺PC的網關地址和交換機之間的`網段地址：
//進入VLAN接口配置模式：
[S3526A]interface Vlan-interface 2
//配置三層VLAN路由接口地址
[S3526A-Vlan-interface2]ip address
[S3526A-Vlan-interface2] interface Vlan-interface 3
[S3526A-Vlan-interface3]ip address
[S3526A-Vlan-interface3] interface Vlan-interface 4
[S3526A-Vlan-interface4]ip address
[S3526B]interface Vlan-interface 2
[S3526B-Vlan-interface2]ip address
[S3526B-Vlan-interface2] interface Vlan-interface 4
[S3526B-Vlan-interface4]ip address
在二臺三層交換機上配置非直連網段靜態路由：
[S3526A]ip route-static
[S3526B]ip route-static
[S3526B]ip route-static
檢視路由表，檢視網絡互通情況：
[S3526B]display ip routing-table
Routing Table: public net
Destination/Mask Proto Pre Cost Nexthop Interface
STATIC 60 0 Vlan-interface4
STATIC 60 0 Vlan-interface4
DIRECT 0 0 Vlan-interface2
DIREC T 0 0 InLoopBack0
DIRECT 0 0 Vlan-interface4
DIRECT 0 0 InLoopBack0
DIRECT 0 0 InLoopBack0
DIRECT 0 0 InLoopBack0
RlP協議在三層交換機上的配置
1.繼續上面的，刪除前面配置的靜態路由。
[S3526A]undo ip route-static
[S3526B]undo ip route-static
[S3526B]undo ip route-static
2.配置RIP協議：
//交換機B上啓用RIP協議
[S3526A]rip
[S3526A-rip]network
[S3526A-rip]network
[S3526A-rip]network
//交換機B上啓用RIP協議
[S3526B]rip
[S3526B-rip]network
[S3526B-rip]network
配置完成即可實現網絡互通
檢視路由表，檢視網絡互通情況：
[S3526B]display ip routing-table
Routing Table: public net
Destination/Mask Proto Pre Cost Nexthop Interface
STATIC 60 0 Vlan-interface4
STATIC 60 0 Vlan-interface4
DIRECT 0 0 Vlan-interface2
DIREC T 0 0 InLoopBack0
DIRECT 0 0 Vlan-interface4
DIRECT 0 0 InLoopBack0
DIRECT 0 0 InLoopBack0
DIRECT 0 0 InLoopBack0
檢視RlP配置資訊如下：
[S3526B-rip]display rip
RIP is turned on
public net VPN-Instance
Checkzero is on Default cost : 1
Summary is on Preference : 100
No peer router
Network :